Column Guard

HEAVY COLUMN GUARDS

A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z

ASTEROID® (CG-2165)
The Asteroid® is the only heavy duty corner guard made of vinyl and is used where its "safety yellow" color is needed to mark driveways, or edges of marine docks. Smudges may be wiped off with solvent or detergent.

SPECIFICATIONS
Thickness: 0.375" at corner tapering to 0.187"
Lengths: 4', 6', 8', 12' custom cut lengths up to 12'
Weight: 1-1/2 lbs./ft.
Flange Width: 4" x 4" (I.D.)
Colors: (1)Black, (3)Tan, (4)Brown, (5)Gray, (70)Safety Yellow.

CODES, CERTIFICATION
Impact Resistance: 465 absorbed (ASTM D-2632)
Abrasion Resistance: 96 (ASTM-1630)
Ozone: Excellent (ASTM-1149)
Lo-Temp: Brittleness -20 °F (ASTM D-746)

Shop Drawing

CG-2165

ASSEMBLY, INSTALLATION
Install using a combination of Epoxy adhesive and mechanical fasteners (lag screws into wood surfaces, lock bolts into concrete, etc). Optional installation with 3/8" x 2-1/2" flat head countersunk bolts with expansion shield 3 bolts per 48" side. Use whatever the job conditions dictate.

Back to the top

CELESTIAL® (CG-2237)
The Celestial® Column Guard is the only flat guard that is able to be used in long strips or wrapped around columns. It helps guard against bumps and knocks caused by equipment or vehicles.

SPECIFICATIONS (Div. 11 Parking Equipment) Material: EPDM Rubber Thickness: 1.5" Length: Maximum 12 ft. Height: 8" Weight: 6 lbs./ft. Color: (1)Black.
CODES, CERTIFICATION Impact Resistance: 75% absorbed (ASTM D-2632) Abrasion Index: 160 (ASTM-1630) Ozone: Excellent (ASTM-1149) Lo-Temp: Brittleness -50°F (ASTM D-746) ASSEMBLY, INSTALLATION Celestial® may be installed horizontally as a wall or parking garage bumper-stop and as a column guard. Use a combination of epoxy adhesive and mechanical fasteners in recessed grooves as dictated by job conditions (lag screws for wood surfaces, lock bolts into concrete, etc). Banding is commonly used when wrapping the Celestial guard around columns, using the grooves to hold the straps in place. CAUTION: Not available for use with columns less than 18" of diameter. Column diameter must be indicated on order so that ends of the guard can be angle-cut at the factory for perfect fit on the jobsite.

Back to the top

GALAXY® (CG-2153)
Industrial corner/column guard also offers maximum protection against damage to both vehicle and structure. Galaxy® is made from SBR rubber that is resistant to most chemicals and ozone. Fits either square or radius corners.

SPECIFICATIONS
(Div. 11 Parking Equipment)
Thickness: 0.625" at corner
Lengths: 4 ft., 6 ft., 8 ft., 10 ft., special lengths up to 10 ft.
Flange Width: 4" x 4" (I.D.)
Weight: 2.2 lbs./ft.
Color: (1)Black

Shop Drawing

CG-2153

ASSEMBLY, INSTALLATION
Install using a combination of epoxy adhesive and mechanical fasteners as dictated by the job conditions; that is, lag screws into wood surfaces, lock bolts into concrete, etc. Flat head fasteners should be used and "pulled" flush into guard surface.

Back to the top

QUASAR® (CG-2148)
Is a hefty corner protector for both vehicle and building. Made of natural rubber with chamfered corners, it is designed to fit parking garage columns.

SPECIFICATIONS
(Div. 11 Parking Equipment)
Thickness: 0.75" at corner
Length: 4 ft., 8 ft., special lengths up to 8 ft.
Flange Width: 4" x 4" (I.D.)
Weight: 2.7 lbs./ft.
Color: (5)Gray
ASSEMBLY, INSTALLATION: The same as GALAXY®

Shop Drawing

CG-2148

Back to the top

STAR® (CG-2150)
Industrial weight corner/column guards offer maximum protection against damage to both vehicle and structure due to impact and/or abrasion. Star® is made from natural rubber.

SPECIFICATIONS
(Div. 11 Parking Equipment)
Thickness: 0.875" at corner
Lengths: 4 ft, 6 ft., 8 ft., 10 ft. 12 ft., special lengths up to 12 ft.
Flange Width: 4" x 4" (I.D.)
Weight: 2.6 lbs./ft.
Color: (5)Gray.
ASSEMBLY, INSTALLATION: The same as GALAXY®

Back to the top

UTE® (WG-2199)
The Ute® Wall guard is made of tough, yet light in weight, Urethane. This non-marking material is easily installed either vertically or horizontally using bolts, screws or mechanical fasteners. Because of its weight, shipping and handling costs are minimal.

SPECIFICATIONS
Thickness: 1.25"
Length: 10 ft.
Height: 8"
Weight: 13 lbs. each
Bolt Size: 3/8" x 3-3/4" round head.
Accessories: End caps, outside corners and retainer washer.
Color: (38)Charcoal.
Specify: Drilled or Undrilled.

Shop Drawing

WG-2199

Back to the top